Part of Curriculum: CDC, RDC and Low-Power RTL (Module 7: Programmable Clock Dividers)
View Full Roadmap →
Level 5 Hard 50 pts ✓ Solved

Programmable Clock Divider

Sequential Design · sequential, clock

A generalized version of divide-by-3: the division amount is set by a runtime input instead of being hardwired into the design.

Write a synthesizable Verilog module named top_module matching the ports below exactly.
📐 Circuit Schematic Diagram
div[3:0]pulse_out>clkrst_nPROGRAMMABLE CLOCK DRAM / STORAGE ARRAY
⚡ Timing & Synthesizability Constraints

Timing Contract: Strict synchronous timing aligned to posedge clk or zero-delay combinational propagation.

RTL Constraints: Synthesizable Verilog-2001. No # delays in synthesizable RTL.

Concept: cnt wraps at div-1 instead of a fixed constant: if (cnt >= div-1) cnt<=0; else cnt<=cnt+1;. The -1 matters — comparing against div instead gives a period one cycle longer than requested, the exact off-by-one that divide-by-3 warns about generalized to any N.
NameDirWidthDescription
clkinput1Input clock
rstinput1Sync active-high reset
divinput4Divide value (period in input clocks), ≥1
pulse_outoutput1High for 1 cycle out of every div cycles
Expected Waveform (Golden Timing Contract)
Verilog-2001 / SV Saved
Font: |
// Click Run Tests (or press Ctrl+Enter) to compile your RTL and simulate against hidden testbenches.
Simulation Timing Diagram (VCD Waveform)
100%
No simulation waveform yet. Run tests to simulate and generate VCD traces.
No compilation run yet. Syntax warnings and elaboration messages will appear here.
No simulation output yet. Raw stdout from vvp will appear here.

RTL Problems / Level 5 · Sequential Design

What You Will Learn

By solving Programmable Clock Divider, you will acquire core industry skills:

  • Synthesizable hardware modeling in standard Verilog-2001 / SystemVerilog.
  • Correct handling of interface port contracts, edge-triggered clocks, and active-low/high resets.
  • Simulation waveform interpretation and debugging using timing diagrams (VCD traces).
  • Architectural avoidance of timing violations, glitching hazards, and synthesis warnings.

Problem Statement & Requirements

A generalized version of divide-by-3: the division amount is set by a runtime input instead of being hardwired into the design.

Hardware design teams at leading semiconductor firms evaluate these exact port contracts, race-condition assertions, and corner cases during technical design reviews and ASIC engineer interviews.

Concept: cnt wraps at div-1 instead of a fixed constant: if (cnt >= div-1) cnt<=0; else cnt<=cnt+1;. The -1 matters — comparing against div instead gives a period one cycle longer than requested, the exact off-by-one that divide-by-3 warns about generalized to any N.

Port List & Interface Timing

The hidden testbench instantiates top_module. Module port names and bit-widths must match the interface contract exactly:

NameDirWidthDescription
clkinput1Input clock
rstinput1Sync active-high reset
divinput4Divide value (period in input clocks), ≥1
pulse_outoutput1High for 1 cycle out of every div cycles

Timing Constraints & Synthesizable RTL Rules

⚡ Synthesizable Implementation Guidelines

Timing Contract: Strict synchronous timing aligned to posedge clk or zero-delay combinational propagation.

Synthesis Constraints: Synthesizable Verilog-2001. No # delays in synthesizable RTL.

Starter RTL Code

module top_module(
  input  clk,
  input  rst,
  input  [3:0] div,
  output pulse_out
);

  // Your code here — counter wraps at div-1, not a fixed constant.

endmodule
Advertisement

Related RTL Problems in Level 5

  • Push/Pop Stack Pointer — A 4-bit stack pointer that moves up on push and down on pop, refusing to overflow past 15 or underflow past 0.
  • Synchronous 8x8 RAM — A minimal single-port RAM: 8 words of 8 bits each, with a registered (one-cycle-delayed) read — the standard timing behavior of real block RAM.
  • FIFO Occupancy Counter — Track exactly how many words are sitting in an 8-deep FIFO — not just full/empty booleans, but the actual live count, including the tricky case of a simultaneous push and pop.

Frequently Asked Questions

What does Programmable Clock Divider require?

A generalized version of divide-by-3: the division amount is set by a runtime input instead of being hardwired into the design. Implement it as Verilog module top_module matching the listed ports.

Is this design combinational or sequential?

Tags: sequential, clock. If a clock signal is present in the port table, implement it as sequential logic; otherwise, use continuous assignments or combinational blocks.

How is my solution graded?

A hidden SystemVerilog testbench simulates your module in the cloud judge. You pass when all directed corner cases match the golden model and the VCD timing waveform matches the contract.

How does this challenge help with semiconductor interviews?

Technical interviewers at NVIDIA, Qualcomm, Apple, and Intel routinely ask candidates to code, debug, and explain the timing waveforms of Programmable Clock Divider to assess real-world synthesizability and race-condition awareness.

Advertisement