Part of Curriculum: Sequential RTL Design (Module 7: Edge Detectors & Pulse Generators)
View Full Roadmap →
Level 2 Medium ★ Flagship #20 25 pts ✓ Solved

Rising Edge Detector — Edge Detection

Sequential Logic · sequential, fsm, counters, medium, edge-detectors

Detect rising transitions ($0 \to 1$) on an asynchronous or multi-cycle input signal `in`, generating a single-clock-cycle pulse `p_edge`.

Write a synthesizable Verilog module named top_module matching the ports below exactly.
📐 Circuit Schematic Diagram
inp_edge>clkrst_nRISING EDGE DETECTORDIGITAL HARDWARE BLOCK
⚡ Timing & Synthesizability Constraints

Timing Contract: Output `p_edge` asserts for exactly one clock cycle immediately following the cycle where `in` transitioned from 0 to 1.

RTL Constraints: Single-cycle pulse output. Synthesizable sequential RTL.

Objective: Understand delayed flop history registers, transition detection, and pulse generation.

Prerequisites: D flip-flops, boolean logic, edge transitions.
NameDirWidthDescription
clkinput1Master sampling clock
areset_ninput1Active-low asynchronous reset
ininput1Input signal to monitor
p_edgeoutput1Single-cycle pulse asserted on 0->1 rising edge
Expected Waveform (Golden Timing Contract)
💡 Need Guidance? Progressive Hints (3 Levels)
Hint 1: Conceptual Direction & Hardware Primitives
Store the previous state of `in` in a register: `always @(posedge clk) in_d <= in;`.
Hint 2: Implementation Architecture & Approach
A rising edge occurs when current input is 1 and previous input was 0: `in & ~in_d`.
Hint 3: Edge Cases, Timing & Verilog Syntax
For a falling edge detector, you would test `~in & in_d`.
🔒 Reveal Verified Reference RTL Solution (Click to expand)
⚠️ Self-Discovery Warning: Try solving and simulating first! Viewing the verified reference implementation will bypass the real debugging experience.
Verified Synthesizable RTL
module top_module(
  input       clk,
  input       areset_n,
  input       in,
  output reg  p_edge
);
  reg in_d;
  always @(posedge clk or negedge areset_n) begin
    if (!areset_n) begin
      in_d   <= 1'b0;
      p_edge <= 1'b0;
    end else begin
      in_d   <= in;
      p_edge <= in & ~in_d;
    end
  end
endmodule
Verilog-2001 / SV Saved
Font: |
// Click Run Tests (or press Ctrl+Enter) to compile your RTL and simulate against hidden testbenches.
Simulation Timing Diagram (VCD Waveform)
100%
No simulation waveform yet. Run tests to simulate and generate VCD traces.
No compilation run yet. Syntax warnings and elaboration messages will appear here.
No simulation output yet. Raw stdout from vvp will appear here.

RTL Problems / Level 2 · Sequential Logic

What You Will Learn

By solving Rising Edge Detector — Edge Detection, you will acquire core industry skills:

  • Synthesizable hardware modeling in standard Verilog-2001 / SystemVerilog.
  • Correct handling of interface port contracts, edge-triggered clocks, and active-low/high resets.
  • Simulation waveform interpretation and debugging using timing diagrams (VCD traces).
  • Architectural avoidance of timing violations, glitching hazards, and synthesis warnings.

Problem Statement & Requirements

Detect rising transitions ($0 \to 1$) on an asynchronous or multi-cycle input signal `in`, generating a single-clock-cycle pulse `p_edge`.

Hardware design teams at leading semiconductor firms evaluate these exact port contracts, race-condition assertions, and corner cases during technical design reviews and ASIC engineer interviews.

Objective: Understand delayed flop history registers, transition detection, and pulse generation.

Prerequisites: D flip-flops, boolean logic, edge transitions.

Port List & Interface Timing

The hidden testbench instantiates top_module. Module port names and bit-widths must match the interface contract exactly:

NameDirWidthDescription
clkinput1Master sampling clock
areset_ninput1Active-low asynchronous reset
ininput1Input signal to monitor
p_edgeoutput1Single-cycle pulse asserted on 0->1 rising edge

Timing Constraints & Synthesizable RTL Rules

⚡ Synthesizable Implementation Guidelines

Timing Contract: Output `p_edge` asserts for exactly one clock cycle immediately following the cycle where `in` transitioned from 0 to 1.

Synthesis Constraints: Single-cycle pulse output. Synthesizable sequential RTL.

Architectural Deep Dive & Implementation Walkthrough

By registering the input signal, `in_d` holds the value of `in` from exactly one clock cycle in the past. Comparing the current value with the delayed value ($in \cdot \overline{in_d}$) evaluates to 1 exclusively during the single clock period when the signal transitioned from 0 to 1.

Common RTL Designer Pitfalls

⚠️ Common Mistakes to Avoid

['Using `in_d & ~in`, which detects falling edges ($1 \\to 0$) instead of rising edges.', 'Forgetting that if `in` originates in an asynchronous domain, it must first pass through a 2-flop synchronizer before edge detection to avoid metastability.']

Silicon & Hardware Engineering Notes

🛠️ ASIC vs FPGA Hardware Considerations

Edge detectors are ubiquitous in pushbutton debouncers, interrupt request latching, and protocol start-bit monitors.

Starter RTL Code

module top_module(
  input   clk,
  input   areset_n,
  input   in,
  output reg p_edge
);

  // Detect rising edge on 'in'

endmodule

Verified Reference Solution

🔒 Reveal Verified Reference RTL Solution
module top_module(
  input       clk,
  input       areset_n,
  input       in,
  output reg  p_edge
);
  reg in_d;
  always @(posedge clk or negedge areset_n) begin
    if (!areset_n) begin
      in_d   <= 1'b0;
      p_edge <= 1'b0;
    end else begin
      in_d   <= in;
      p_edge <= in & ~in_d;
    end
  end
endmodule
Advertisement

Related RTL Problems in Level 2

Frequently Asked Questions

What does Rising Edge Detector — Edge Detection require?

Detect rising transitions ($0 \to 1$) on an asynchronous or multi-cycle input signal `in`, generating a single-clock-cycle pulse `p_edge`. Implement it as Verilog module top_module matching the listed ports.

Is this design combinational or sequential?

Tags: sequential, fsm, counters, medium, edge-detectors. If a clock signal is present in the port table, implement it as sequential logic; otherwise, use continuous assignments or combinational blocks.

How is my solution graded?

A hidden SystemVerilog testbench simulates your module in the cloud judge. You pass when all directed corner cases match the golden model and the VCD timing waveform matches the contract.

How does this challenge help with semiconductor interviews?

Technical interviewers at NVIDIA, Qualcomm, Apple, and Intel routinely ask candidates to code, debug, and explain the timing waveforms of Rising Edge Detector — Edge Detection to assess real-world synthesizability and race-condition awareness.

Advertisement