Part of Curriculum: CDC, RDC and Low-Power RTL (Module 11: Voltage Margin & Brownout Monitors)
View Full Roadmap →
Level 7 Medium 25 pts ✓ Solved

Brown-Out Reset Detector

Sequential Design · sequential, power, reset

Trigger a reset when the supply voltage dips too low — and use two different thresholds for asserting vs. releasing it, so noise near the edge can't chatter the reset line.

Write a synthesizable Verilog module named top_module matching the ports below exactly.
📐 Circuit Schematic Diagram
vsense[7:0]reset_out>clkrst_nBROWN-OUT RESET DETEDIGITAL HARDWARE BLOCK
⚡ Timing & Synthesizability Constraints

Timing Contract: Strict synchronous timing aligned to posedge clk or zero-delay combinational propagation.

RTL Constraints: Synthesizable Verilog-2001. No # delays in synthesizable RTL.

Concept: A real brown-out detector uses hysteresis: reset asserts when voltage drops below a LOW threshold, but only releases once voltage climbs back above a separate, higher HIGH threshold — the gap between the two thresholds is a noise margin. Using the same threshold for both directions collapses that margin to zero: the moment voltage ticks back above the single threshold, reset releases immediately, even if it's still sitting in what should be the unsafe hysteresis band — exactly the chattering behavior hysteresis exists to prevent.
NameDirWidthDescription
clkinput1Clock
rst_extinput1External force-reset input
vsenseinput8Sensed supply voltage (arbitrary units)
reset_outoutput11 while held in brown-out reset
Expected Waveform (Golden Timing Contract)
Verilog-2001 / SV Saved
Font: |
// Click Run Tests (or press Ctrl+Enter) to compile your RTL and simulate against hidden testbenches.
Simulation Timing Diagram (VCD Waveform)
100%
No simulation waveform yet. Run tests to simulate and generate VCD traces.
No compilation run yet. Syntax warnings and elaboration messages will appear here.
No simulation output yet. Raw stdout from vvp will appear here.

RTL Problems / Level 7 · Sequential Design

What You Will Learn

By solving Brown-Out Reset Detector, you will acquire core industry skills:

  • Synthesizable hardware modeling in standard Verilog-2001 / SystemVerilog.
  • Correct handling of interface port contracts, edge-triggered clocks, and active-low/high resets.
  • Simulation waveform interpretation and debugging using timing diagrams (VCD traces).
  • Architectural avoidance of timing violations, glitching hazards, and synthesis warnings.

Problem Statement & Requirements

Trigger a reset when the supply voltage dips too low — and use two different thresholds for asserting vs. releasing it, so noise near the edge can't chatter the reset line.

Hardware design teams at leading semiconductor firms evaluate these exact port contracts, race-condition assertions, and corner cases during technical design reviews and ASIC engineer interviews.

Concept: A real brown-out detector uses hysteresis: reset asserts when voltage drops below a LOW threshold, but only releases once voltage climbs back above a separate, higher HIGH threshold — the gap between the two thresholds is a noise margin. Using the same threshold for both directions collapses that margin to zero: the moment voltage ticks back above the single threshold, reset releases immediately, even if it's still sitting in what should be the unsafe hysteresis band — exactly the chattering behavior hysteresis exists to prevent.

Port List & Interface Timing

The hidden testbench instantiates top_module. Module port names and bit-widths must match the interface contract exactly:

NameDirWidthDescription
clkinput1Clock
rst_extinput1External force-reset input
vsenseinput8Sensed supply voltage (arbitrary units)
reset_outoutput11 while held in brown-out reset

Timing Constraints & Synthesizable RTL Rules

⚡ Synthesizable Implementation Guidelines

Timing Contract: Strict synchronous timing aligned to posedge clk or zero-delay combinational propagation.

Synthesis Constraints: Synthesizable Verilog-2001. No # delays in synthesizable RTL.

Starter RTL Code

module top_module(
  input  clk,
  input  rst_ext,
  input  [7:0] vsense,
  output reg reset_out
);

  // Your code here — LOW=100, HIGH=110. Assert reset when vsense<LOW; release only when vsense>=HIGH.

endmodule
Advertisement

Related RTL Problems in Level 7

  • Async-Assert / Sync-Deassert Reset — Assert reset the instant it goes active, but only release it once it has been clean for 2 clock edges — the standard reset architecture for any real design.
  • 3-Flop CDC Synchronizer — A deeper 3-stage synchronizer for signals that need extra MTBF margin beyond the standard 2-flop chain.
  • Synchronized Rising-Edge Detector — Safely synchronize an asynchronous level signal, then produce a clean single-cycle pulse the moment it rises in the local clock domain.

Frequently Asked Questions

What does Brown-Out Reset Detector require?

Trigger a reset when the supply voltage dips too low — and use two different thresholds for asserting vs. releasing it, so noise near the edge can't chatter the reset line. Implement it as Verilog module top_module matching the listed ports.

Is this design combinational or sequential?

Tags: sequential, power, reset. If a clock signal is present in the port table, implement it as sequential logic; otherwise, use continuous assignments or combinational blocks.

How is my solution graded?

A hidden SystemVerilog testbench simulates your module in the cloud judge. You pass when all directed corner cases match the golden model and the VCD timing waveform matches the contract.

How does this challenge help with semiconductor interviews?

Technical interviewers at NVIDIA, Qualcomm, Apple, and Intel routinely ask candidates to code, debug, and explain the timing waveforms of Brown-Out Reset Detector to assess real-world synthesizability and race-condition awareness.

Advertisement