Part of Curriculum: Sequential RTL Design (Module 1: Sequential Design)
View Full Roadmap →
Level 3 Medium 25 pts ✓ Solved

4-to-8 Bit Gearbox

Sequential Design · sequential, datapath

Pack two 4-bit nibbles arriving one per cycle into a single 8-bit word, pulsing valid only once the pair is complete — the narrow-to-wide half of a SerDes gearbox.

Write a synthesizable Verilog module named top_module matching the ports below exactly.
📐 Circuit Schematic Diagram
in_validin_data[3:0]out_validout_data[7:0]>clkrst_n4-TO-8 BIT GEARBOXDIGITAL HARDWARE BLOCK
⚡ Timing & Synthesizability Constraints

Timing Contract: Strict synchronous timing aligned to posedge clk or zero-delay combinational propagation.

RTL Constraints: Synthesizable Verilog-2001. No # delays in synthesizable RTL.

Concept: A gearbox bridges two datapaths running at different widths (and therefore different word rates) without dropping data. Here, the first nibble is latched and held; when the second nibble arrives, it combines with the held nibble into a full byte, {first_nibble, in_data}, and out_valid pulses for exactly the one cycle the byte is ready — first nibble becomes the upper bits, since it arrived first.
NameDirWidthDescription
clkinput1Clock
rstinput1Sync active-high reset
in_validinput11 when in_data carries a new nibble
in_datainput4Incoming nibble
out_validoutput1Pulses for 1 cycle when a full byte is assembled
out_dataoutput8Assembled byte: first nibble in bits[7:4], second in bits[3:0]
Expected Waveform (Golden Timing Contract)
Verilog-2001 / SV Saved
Font: |
// Click Run Tests (or press Ctrl+Enter) to compile your RTL and simulate against hidden testbenches.
Simulation Timing Diagram (VCD Waveform)
100%
No simulation waveform yet. Run tests to simulate and generate VCD traces.
No compilation run yet. Syntax warnings and elaboration messages will appear here.
No simulation output yet. Raw stdout from vvp will appear here.

RTL Problems / Level 3 · Sequential Design

What You Will Learn

By solving 4-to-8 Bit Gearbox, you will acquire core industry skills:

  • Synthesizable hardware modeling in standard Verilog-2001 / SystemVerilog.
  • Correct handling of interface port contracts, edge-triggered clocks, and active-low/high resets.
  • Simulation waveform interpretation and debugging using timing diagrams (VCD traces).
  • Architectural avoidance of timing violations, glitching hazards, and synthesis warnings.

Problem Statement & Requirements

Pack two 4-bit nibbles arriving one per cycle into a single 8-bit word, pulsing valid only once the pair is complete — the narrow-to-wide half of a SerDes gearbox.

Hardware design teams at leading semiconductor firms evaluate these exact port contracts, race-condition assertions, and corner cases during technical design reviews and ASIC engineer interviews.

Concept: A gearbox bridges two datapaths running at different widths (and therefore different word rates) without dropping data. Here, the first nibble is latched and held; when the second nibble arrives, it combines with the held nibble into a full byte, {first_nibble, in_data}, and out_valid pulses for exactly the one cycle the byte is ready — first nibble becomes the upper bits, since it arrived first.

Port List & Interface Timing

The hidden testbench instantiates top_module. Module port names and bit-widths must match the interface contract exactly:

NameDirWidthDescription
clkinput1Clock
rstinput1Sync active-high reset
in_validinput11 when in_data carries a new nibble
in_datainput4Incoming nibble
out_validoutput1Pulses for 1 cycle when a full byte is assembled
out_dataoutput8Assembled byte: first nibble in bits[7:4], second in bits[3:0]

Timing Constraints & Synthesizable RTL Rules

⚡ Synthesizable Implementation Guidelines

Timing Contract: Strict synchronous timing aligned to posedge clk or zero-delay combinational propagation.

Synthesis Constraints: Synthesizable Verilog-2001. No # delays in synthesizable RTL.

Starter RTL Code

module top_module(
  input  clk,
  input  rst,
  input  in_valid,
  input  [3:0] in_data,
  output reg out_valid,
  output reg [7:0] out_data
);

  // Your code here — latch the first nibble; on the second, pack {first, second} and pulse out_valid.

endmodule
Advertisement

Related RTL Problems in Level 3

Frequently Asked Questions

What does 4-to-8 Bit Gearbox require?

Pack two 4-bit nibbles arriving one per cycle into a single 8-bit word, pulsing valid only once the pair is complete — the narrow-to-wide half of a SerDes gearbox. Implement it as Verilog module top_module matching the listed ports.

Is this design combinational or sequential?

Tags: sequential, datapath. If a clock signal is present in the port table, implement it as sequential logic; otherwise, use continuous assignments or combinational blocks.

How is my solution graded?

A hidden SystemVerilog testbench simulates your module in the cloud judge. You pass when all directed corner cases match the golden model and the VCD timing waveform matches the contract.

How does this challenge help with semiconductor interviews?

Technical interviewers at NVIDIA, Qualcomm, Apple, and Intel routinely ask candidates to code, debug, and explain the timing waveforms of 4-to-8 Bit Gearbox to assess real-world synthesizability and race-condition awareness.

Advertisement