Part of Curriculum: Sequential RTL Design (Module 7: Edge Detectors & Pulse Generators)
View Full Roadmap →
Level 3 Medium 25 pts ✓ Solved

One-Shot Pulse Generator

Sequential Design · sequential, control

Turn a trigger into a clean pulse of a fixed, programmable width — a classic monostable ("one-shot") that ignores any retrigger attempts until the current pulse finishes.

Write a synthesizable Verilog module named top_module matching the ports below exactly.
📐 Circuit Schematic Diagram
triggerwidth[3:0]pulse_out>clkrst_nONE-SHOT PULSE GENERDIGITAL HARDWARE BLOCK
⚡ Timing & Synthesizability Constraints

Timing Contract: Strict synchronous timing aligned to posedge clk or zero-delay combinational propagation.

RTL Constraints: Synthesizable Verilog-2001. No # delays in synthesizable RTL.

Concept: A one-shot latches an active flag on trigger, counts down for width cycles, and only accepts a new trigger once it's back to idle: if (!active && trigger) is the guard that makes retriggering impossible mid-pulse. Dropping the !active half of that guard (just checking trigger alone) lets a retrigger reload the countdown while a pulse is already running, silently stretching the output well past its intended, fixed width — defeating the entire point of a one-shot.
NameDirWidthDescription
clkinput1Clock
rstinput1Sync active-high reset
triggerinput1Pulse for 1 cycle to fire a new one-shot (ignored while already active)
widthinput4Pulse width in cycles
pulse_outoutput1High for exactly width cycles after each accepted trigger
Expected Waveform (Golden Timing Contract)
Verilog-2001 / SV Saved
Font: |
// Click Run Tests (or press Ctrl+Enter) to compile your RTL and simulate against hidden testbenches.
Simulation Timing Diagram (VCD Waveform)
100%
No simulation waveform yet. Run tests to simulate and generate VCD traces.
No compilation run yet. Syntax warnings and elaboration messages will appear here.
No simulation output yet. Raw stdout from vvp will appear here.

RTL Problems / Level 3 · Sequential Design

What You Will Learn

By solving One-Shot Pulse Generator, you will acquire core industry skills:

  • Synthesizable hardware modeling in standard Verilog-2001 / SystemVerilog.
  • Correct handling of interface port contracts, edge-triggered clocks, and active-low/high resets.
  • Simulation waveform interpretation and debugging using timing diagrams (VCD traces).
  • Architectural avoidance of timing violations, glitching hazards, and synthesis warnings.

Problem Statement & Requirements

Turn a trigger into a clean pulse of a fixed, programmable width — a classic monostable ("one-shot") that ignores any retrigger attempts until the current pulse finishes.

Hardware design teams at leading semiconductor firms evaluate these exact port contracts, race-condition assertions, and corner cases during technical design reviews and ASIC engineer interviews.

Concept: A one-shot latches an active flag on trigger, counts down for width cycles, and only accepts a new trigger once it's back to idle: if (!active && trigger) is the guard that makes retriggering impossible mid-pulse. Dropping the !active half of that guard (just checking trigger alone) lets a retrigger reload the countdown while a pulse is already running, silently stretching the output well past its intended, fixed width — defeating the entire point of a one-shot.

Port List & Interface Timing

The hidden testbench instantiates top_module. Module port names and bit-widths must match the interface contract exactly:

NameDirWidthDescription
clkinput1Clock
rstinput1Sync active-high reset
triggerinput1Pulse for 1 cycle to fire a new one-shot (ignored while already active)
widthinput4Pulse width in cycles
pulse_outoutput1High for exactly width cycles after each accepted trigger

Timing Constraints & Synthesizable RTL Rules

⚡ Synthesizable Implementation Guidelines

Timing Contract: Strict synchronous timing aligned to posedge clk or zero-delay combinational propagation.

Synthesis Constraints: Synthesizable Verilog-2001. No # delays in synthesizable RTL.

Starter RTL Code

module top_module(
  input  clk,
  input  rst,
  input  trigger,
  input  [3:0] width,
  output reg pulse_out
);

  // Your code here — on an accepted trigger (only when not already active), go high for exactly width cycles.

endmodule
Advertisement

Related RTL Problems in Level 3

Frequently Asked Questions

What does One-Shot Pulse Generator require?

Turn a trigger into a clean pulse of a fixed, programmable width — a classic monostable ("one-shot") that ignores any retrigger attempts until the current pulse finishes. Implement it as Verilog module top_module matching the listed ports.

Is this design combinational or sequential?

Tags: sequential, control. If a clock signal is present in the port table, implement it as sequential logic; otherwise, use continuous assignments or combinational blocks.

How is my solution graded?

A hidden SystemVerilog testbench simulates your module in the cloud judge. You pass when all directed corner cases match the golden model and the VCD timing waveform matches the contract.

How does this challenge help with semiconductor interviews?

Technical interviewers at NVIDIA, Qualcomm, Apple, and Intel routinely ask candidates to code, debug, and explain the timing waveforms of One-Shot Pulse Generator to assess real-world synthesizability and race-condition awareness.

Advertisement